Page 12 - Product Catalogue

Ceramic Adhesives

YURTBAY FLEXIBLE 2K

DEFORMABLE TILE ADHESIVE
YURTBAY FLEXIBLE 2K is a two component, cement and polymer emulsion based
adhesive mortar with high adhesion strength, high flexibility, reduced slip,
longer operation time, resistance against water
and frost and heat change. TS EN 12004-1 C2TE S2

FIELDS OF APPLICATION surface within 30 min. Wide expansion joints are required to
It is used for medium and large size floor and wall tiling, natural be left for every 50 m² during application. The prepared mortar
rock, travertine, marble, granite, porcelain ceramic, decorative should be used up within 3 hours.
brick etc. coating materials, at interior and exterior horizontal and APPLICATION REQUIREMENTS
vertical applications. •The ambient and substrate temperature should be in the range of
APPLICATION EXAMPLES +5 °C to 35 °C.
Interior wall: Cement based plaster, gypsum and concrete floors, •Should not be applied on frozen, thawing surfaces and surfaces
old ceramic coating with a frost hazard.
Interior floor: Cement based screed surfaces (provided that the •Application should not be made when the substrate temperature
surface sets sufficiently and is dry) and concrete coatings, old is high, and during very sunny or extremely windy weather.
ceramic coating WARNINGS AND RECOMMENDATIONS
Exterior: Cement based screed and concrete coating, old ceramic •If crusting occurs on the material during open time, the material
coating should be applied after being re-mixed.
APPLICATION DATA (23 °C & 50% B.N) •It is not recommended to re-wet the material if there is crusting
Product type : Powder and liquid in the material.
Product color : Gray •Any foreign substances should absolutely not be added.
Mixing ratio : 6 L liquid component for a 25 kg mixture • Gypsum and similar surfaces with high water absorption should be
Pot life : Max. 2 ho1urs primed before application to reduce water absorption.
Application temperature : between +5 °C +35 °C CONSUMPTION
Open time : 30 minutes (as per TS EN 12004-1) Consumption amount per 1 m .
2
Ready for Use : Min. 24 hours (light pedestrian traffic)
Required time for grouting : Min. 24 hours Application Notch Size Consumption Amount (Kg/m )
2
Full setting duration : 28 days One-sided adhesion 6x6x6 mm 3-4 kg
SURFACE PREPARATION One-sided adhesion 8x8x8 4-5 kg
Substrates on which application will be made should be clean and
sound. Any dust, oil, dirt and materials that will prevent adhesion Note: Provided consumption values are approximate values, and
should be removed from the surface and mortar, cement, etc. may vary depending on the area of the application surface and the
residues should be scraped off. Surface defects with depth more application thickness.
than 2 cm should be repaired at least 1 day in advance. SHELF LIFE
MIXTURE PREPARATION 12 months from production date when stored in non-humid, dry
Clean water of 6 L is poured into a clean, round container; then, environments and in original packing.
a 25 kg powder product should be added slowly and mixed until a The packages should be tightly closed when not in use.
homogeneous, pellet free appearance is obtained. mixing should *These values have been obtained as a result of laboratory tests
be made using a low speed mixer. The fresh mixture should be in compliance with the standards. The values may vary in different
allowed to mature for 5 min, and re-mixed prior to application. application environments.
APPLICATION
The mixed YURTBAY FLEXIBLE 2K mortar should be applied on BAG PALLET
the substrate using a steel notched trowel, with a notch size Bag Weight / kg AMOUNT / BAG GROSS WEIGHT / kg SIZE / cm
appropriate to the tile dimensions. The coating material is placed 25 54 1370 80x110x105
on the surface and ensured to be fitted on the surface using
a rubber mallet. Adhesive mortar should also be filled into the
bottom holes of the tiles, in bonding the tiles larger than 40x40
cm in exterior applications. the tiles should be adhered to the

9