Page 10 - Product Catalogue

Ceramic Adhesives

YURTBAY FLEXIBLE 1K

DEFORMABLE TILE ADHESIVE
YURTBAY FLEX is a flexible, cement-based, high adhesion
strength, slip resistant, ceramic adhesive
mortar with extended open time.
C2TE S1
TS EN 12004-1
FIELDS OF APPLICATION cm in exterior applications. the tiles should be adhered to the
It is used for medium and large size floor and wall tiling, natural surface within 30 min. Wide expansion joints are required to
rock, travertine, marble, granite, porcelain ceramic, decorative be left for every 50 m² during application. The prepared mortar
brick etc. coating materials, at Interior and exterior horizontal and should be used up within 3 hours.
vertical applications. APPLICATION REQUIREMENTS
APPLICATION EXAMPLES • The ambient and substrate temperature should be in the range
Interior wall: Cement based plaster, gypsum and concrete floors, of +5 °C to 35 °C.
old ceramic coating • Should not be applied on frozen, thawing surfaces and surfaces
Interior floor: Cement based screed surfaces (provided that with a frost hazard.
the surface sets sufficiently and is dry) and concrete floors, old • Application should not be made when the substrate temperature
ceramic coating is high, and during very sunny or extremely windy weather.
Exterior: Cement based screed and concrete coating, old ceramic WARNINGS AND RECOMMENDATIONS
coating • If crusting occurs on the material during open time, the material
APPLICATION DATA (23 °C & 50% B.N) should be applied after being re-mixed.
Product type : Powder • It is not recommended to re-wet the material if there is crusting
Product color : Gray and white in the material.
mixing ratio : 6-6,5 L water for 25 kg mixture • Any foreign substances should absolutely not be added.
Pot life : Max. 3 hours • Gypsum and similar surfaces with high water absorption should
Application temperature : between +5 °C +35 °C be primed before application to reduce water absorption.
Open time : 30 minutes (as per TS EN 12004-1) CONSUMPTION
Ready for Use : Min. 24 hours (light pedestrian traffic) Consumption amount per 1 m .
2
Required time for grouting : Min. 24 hours
Full setting duration : 28 days Application Notch Size Consumption Amount (Kg/m ) 2
SURFACE PREPARATION One-sided adhesion 6x6x6 mm 3-4 kg
Substrates on which application will be made should be clean and One-sided adhesion 8x8x8 4-5 kg
sound. Any dust, oil, dirt and materials that will prevent adhesion
should be removed from the surface and mortar, cement, etc. Note: Provided consumption values are approximate values, and
residues should be scraped off. Surface defects with depth more may vary depending on the area of the application surface and the
than 2 cm should be repaired at least 1 day in advance. application thickness.
MIXTURE PREPARATION SHELF LIFE
Clean water of 6-6,5 L is poured into a clean, round container; 12 months from production date when stored in non-humid, dry
then, a 25 kg powder product should be added slowly and mixed environments and in original packing.
until a homogeneous, pellet free appearance is obtained. The packages should be tightly closed when not in use.
mixing should be made using a low speed mixer. The fresh mixture *These values have been obtained as a result of laboratory tests
should be allowed to mature for 5 min, and re-mixed prior to in compliance with the standards. The values may vary in different
application. application environments.
APPLICATION
The mixed YURTBAY FLEXIBLE 1K mortar should be applied on BAG PALLET
the substrate using a steel notched trowel, with a notch size Bag Weight / kg AMOUNT / BAG GROSS WEIGHT / kg SIZE / cm
appropriate to the tile dimensions. The coating material is placed 25 54 1370 80x110x105
on the surface and ensured to be fitted on the surface using
a rubber mallet. Adhesive mortar should also be filled into the
bottom holes of the tiles, in bonding the tiles larger than 40x40

7